CAA Sensors

• 

  Dew Point Sensor

  Dew Point Sensor for Refrigerant and Membrane dryers

  USD $621 – USD $1,149Price range: USD $621 through USD $1,149

  Dew point sensor with polymer technology for compressed air and inert, non-corrosive gases. Ideal for temporary or permanent installation.

  Pressure Dew Point (PDP) Range: -60°C to +60°C (-76°F to +140°F)

  Dryer Types: Refrigerant, Membrane, Drum or Hybrid dryers

  Outputs: Modbus (RS485) and 4-20mA

  Power requirement: 10 to 30vDC, max 50 mA @ 24vDC

  Applications
  • Compressed air and inert, non-corrosive gas systems
  • Process gases
  • Manufacturing, industrial and pharmaceutical use
  • Non-explosive environments

  Select options
• 

  Flow Meter - Gas and Steam

  Mini Flow Meter for Point of Use

  USD $546 – USD $1,084Price range: USD $546 through USD $1,084

  Mini flow sensor, ideal for low flow, small pipes and point of use measurements. Measure instantaneous flow and cumulative flow

  Pipe Sizes: DN3 to DN40

  Pipe Connection: NPT or G thread

  Accuracy: ±1.5% reading, ±0.3% full scale

  Output: Modbus (RS485) and 4-20mA

  Power Requirement: 24VDC

  Application
  • Clean and dry compressed air and inert gases
  • Point of use measurements
  • Manufacturing, industrial and pharmaceutical use
  • Temporary or permanent installation

  Select options
• 

  HMI / Display

  HMI / Display for a Single Sensor

  USD $756

  HMI / Display for a Single Sensor

  HMI / Display for a single sensor. Use with CAA Sensors’ flow meters, dew point sensors or pressure sensors. Ideal for viewing live data and graphs from sensors that (i) don’t have a built-in display, or (ii) are installed in locations that are difficult to access, or (iii) are installed in remote locations.

  Standard Features

  • 4.3″ TFT LCD touch screen
  • Wall mount
  • Modbus RTU input
  • Modbus RTU output
  • IP65 protection
  • Power supply: 85 ~ 264 VAC

  Applications

  • Manufacturing, industrial and pharmaceutical use
  • Permanent or temporary installation
  • Non-explosive environments

  Select options
• 

  Dew Point Sensor

  Mini Dew Point Sensor for Refrigerant and Membrane dryers

  USD $557 – USD $608Price range: USD $557 through USD $608

  This economical, mini dew point sensor is suited to small spaces. Measure pressure dew point (PDP), relative humidity, temperature. Ideal for temporary or permanent installation.

  Pressure Dew Point (PDP) Range: -60°C to +60°C (-76°F to +140°F)

  Dryer Types: Refrigerant, Drum or Membrane Dryers
  

  Outputs: Modbus (RS485) and 4-20mA

  Power Requirement: 10 to 30vDC, max 50 mA @ 24vDC

  Application
  • Compressed air and inert, non-corrosive gas systems
  • Process gases
  • Manufacturing, industrial and pharmaceutical use
  • Permanent or temporary measurements
  • Non-explosive environments

  Select options
• 

  Accessories

  Hot Tap Clamps

  USD $359 – USD $592Price range: USD $359 through USD $592

  Compressed Air Alliance’s Hot Tap Clamps are idea for use when a take off or socket needs to be added to the pipework while under pressure. Each set comes with a clamp and a ball valve. The clamps are easy to install around the pipe and form a tight seal.

  Clamp Sizes
  To suit pipe ODs from 45 mm (1.8”) to 240 mm (9.4”)

  Ball Valve Size
  1/2” valve or 3/4” valve
  

  Working Gas Pressure Range
  Up to 1.6 MPa (16 bar, 232 psi)

  Working Temperature
  0°C to 60°C (+32°F to +140°F)

  Clamp Material
  Clamp shell, nuts and washers are made from 316 stainless steel
  Gasket is made from Nitrile rubber

  Applications
  • Manufacturing and industrial use
  • Temporary or permanent installation

  Select options
• 

  Din Rail with Display

  Power Meter – Din Rail with Display

  USD $452 – USD $548Price range: USD $452 through USD $548

  This three-phase power meter with Modbus/RTU output is simple to install and easy to configure directly through the built in display and can be connected to your data acquisition system for long term monitoring. Use on mains supply or to sub meter individual equipment or sub loads. Measure voltage, amps, frequency, kilowatts, kilowatt hours, power factor, reactive power, apparent power and harmonics.

  Measured Voltage: 0~600 VAC

  Mounting: Din Rail

  Output: Modbus RS485

  Comes with 3 Rogowski Coils.  Choose from 500 amps, 1,000 amps or 3,000 amps

  Power requirement: 24 VDC, 45- 60 Hz

  Applications
  • Mains supply and sub metering individual equipment or sub loads
  • Manufacturing, industrial and pharmaceutical use
  • Non-explosive environments

  Select options
• 

  Flow Meter - Gas and Steam

  Compact Flow Meter for Point of Use

  USD $347 – USD $539Price range: USD $347 through USD $539

  Compact inline flow sensor, ideal for low flow, small pipes and point of use measurements. Measure instantaneous flow and cumulative flow in clean and dry compressed air and inert gases.

  Standard Features

  • IP Rating: IP40
  • Accuracy: ±3% full scale ±1 digit
  • Output: Modbus (RS485)
  • Display: Colour crystal display
  • Power Requirement: 24VDC

  Options

  • Pipe sizes for G thread: DN15 (1/2″)  to DN40 (1.5″)
  • Gas Types: Air, Carbon Dioxide, Carbon Monoxide, Nitrogen, Oxygen

  Applications

  • Point of use flow measurements
  • Manufacturing, industrial and pharmaceutical use
  • Permanent or temporary installation
  • Non-explosive environments

  Select options
• 

  Data Acquisition System

  ModuMesh – Wireless Modbus Communication

  USD $473

  ModuMesh is wireless Modbus RS485 mesh device. It allows you to wirelessly transmit data from sensors to a display or data acquisition module, thus removing the need for long runs of cable.

  Standard Features

  • Wireless communication radio frequency:
    • 868MHz (EU)
    • 902-928MHz (Americas, Asia and Australia).
  • Range: Up to 1 km (line of sight)
  • Encrypted communications by AES 128bits
  • IP Rating: IP54
  • Power Requirement: 9 to 30 vDC

  Applications

  • Manufacturing, industrial and pharmaceutical use
  • Temporary or permanent installation
  • Non-explosive environments

  Select options
• 

  Panel Mount

  Power Meter – Panel Mount with Display

  USD $361 – USD $445Price range: USD $361 through USD $445

  This single or three-phase, panel mount power meter is ideal for installation on main or sub-distribution boards where readings need to be accessed without opening the panel. Use on mains supply or to sub meter individual equipment or sub loads. Measure Voltage, amps, frequency, kilowatts, kilowatt hours, power factor, real power, reactive power, apparent power and harmonics.

  Measured Voltage and Frequency: 0~600 VAC Phase Voltage

  Mounting: Panel Mount

  Output: Modbus RS485

  Comes with 3 Rogowski Coils.  Choose from 500 amps, 1,000 amps or 3,000 amps

  Power requirement: 18-36vDC, 45- 60 Hz

  Application
  • Mains supply, sub metering individual equipment or sub loads
  • Manufacturing, industrial or pharmaceutical use
  • Non-explosive environments

  Select options
• 

  Coil with 4-20mA output

  Rogowski Coils with Integrator

  USD $180 – USD $244Price range: USD $180 through USD $244

  Current clamps provide an effective energy measurement solution when your budget is limited. Rogowski Coils have a large flexible coil and provide an excellent solution where a traditional current clamp is too difficult to fit. The inline integrator amplifies and converts the coil’s output to a 4-20mA or Modbus (RS485) standard signal for simple connection to your PLC or display.

  Type: Single phase (Amps), current clamp

  Output Signals: 4 to 20mA or Modbus (RS485)

  Accuracy: ±1%

  Display: No Display

  Rogowski Coils options – Comes with 1 Rogowski coil. Choose from 500 amps, 1,000 amps or 3,000 amps

  Power requirement: 24vDC, 100mW

  Applications
  • Single phase measurements – Amps
  • Manufacturing, industrial and pharmaceutical use
  • Temporary or permanent installation

  Select options
• 

  Pressure Sensor

  Pressure Sensor – 16 bar (232 psi)

  USD $168 – USD $185Price range: USD $168 through USD $185

  Pressure sensor for installation on compressed air and gas systems. Use in wet or dry gas to measure demand, supply and remote pressures. Ideal for temporary or permanent installation.

  Gas Pressure Range: up to 16 bar (232 psi)

  Accuracy: ±1%

  Output: 4-20mA or Modbus

  Power Requirement: 24vDC, < 10mA

  Applications
  • Wet and dry gases
  • Demand, Supply and Remote installations
  • Manufacturing, industrial and pharmaceutical use
  • Non-explosive environments

  Select options
• 

  Accessories

  Flow Meter Enclosure

  USD $176

  Transparent flow meter enclosure, suitable for use with Compressed Air Alliance Flow meters. Protect the flow meter head from water, dust and other damage. Quick installation. Easy to disassemble.

  Material: Transparent polycarbonate shell

  IP Rating: IP66

  Ambient Temperature Range: -20°C to +80°C (-4°F to +176°F)

  Add to cart
• 

  Accessories

  Power Pack

  USD $76

  24vDC Power Pack with M12 connector for use with Compressed Air Alliance’s dew point, flow, pressure and temperature sensors

  • Interchangeable plugs – Australia, UK, Europe and USA
  • 24vDC output – M12, 5 pin female connector
  • 100-240vAC input (50/60 Hz)
  • 50W
  • 2.1 Amp
  • 1.7m cable length

  Add to cart
• 

  Accessories

  Cables

  USD $21 – USD $42Price range: USD $21 through USD $42

  5 wire sensor / instrument / data cables. Perfect for connecting sensors to 24vDC power, Modbus output, 4-20mA output, displays, SCADA systems and more.

  These cables can be used with our Data Acquisition System, Dew Point Sensors, Flow Meter, Pressure Sensors, Power Meters and Temperature Sensors.

  Applications

  • Manufacturing, industrial and pharmaceutical use
  • Permanent and temporary installations
  • Non-explosive environments

  Select options
• 

  Accessories

  M12 Connector

  USD $15 – USD $42Price range: USD $15 through USD $42

  5 pin, M12 connectors. Perfect for connecting sensors to Modbus or 4-20mA cables and 24vDC power.

  The Y and Tee connectors are ideally suited to daisy chaining sensors together.

  Select options